Printing characteristics of the hottest metal pack

2022-10-16
  • Detail

Printing characteristics of metal packaging materials

metal is an important packaging material, which plays a very important role in packaging. Unlike ordinary paper and plastic printing, metal printing has its own printing characteristics, and has special requirements on the ink materials used

1. The reasonable selection of metal printing coating, glazing oil

coating and glazing oil is the key to the quality of metal printing products. Reasonable selection of coatings and varnishes is the premise to ensure that metal printing products have good firmness, color, whiteness, gloss and processing suitability. According to different uses, metal printing coatings can be divided into primer, white paint, glazing oil, inner wall paint, edge seam paint and so on. The side seam paint can be divided into inner side seam paint and outer side seam paint. After the inner side seam paint is dried, it is required to meet the food hygiene requirements

2. metal printing ink

metal printing ink is a special ink printed on tinplate and other metal sheets, which is mainly composed of pigments, binders, fillers and auxiliary agents

in addition to the printability of general offset printing inks, metal printing inks should also have the following characteristics:

(1) impact resistance and strong adhesion. In the process of post press processing, metal materials such as tinplate need to go through canning processes such as cutting, bending impact, seams, etc., so the ink layer should have sufficient adhesion, so that the printed tinplate can withstand the stamping of the mold, and has excellent machining performance (including flexibility, surface hardness, impact strength, etc.). At the same time, it is required that the ink layer has good lipophilicity, so that it can be well combined with the glazing oil, so as to ensure a certain degree of adhesion between the sheet and the ink layer and the glazing oil

(2) firm and hard. In the process of can making, the printed and polished tinplate will inevitably collide with each other, and the cut tinplate is very sharp, which is easy to damage the pattern on the metal surface and make the ink layer fall off, so the ink layer is required to be firm and hard

(3) heat resistance. In the drying process, the printing piece must go through the heating and drying process at a certain temperature and time. Therefore, pigments and binders with strong heat resistance should be selected to prevent the ink from yellowing after heating

(providing more development opportunities for the industry 4) solvent resistance. In order to make the appearance of metal prints beautiful, improve the hardness, and prevent damage caused by friction, it needs polishing. Glazing oil contains a lot of strong solvents, which requires that the ink layer after drying does not change color, expand or shrink

(5) light resistance. Gold step 1 pollution reduction belongs to the container. Under sunlight and light, the color of the pattern is required not to change color

(6) cooking resistance. Some metal cans need to be boiled. Nanshan aluminum takes the lead in breaking through the monopoly of sterilization treatment or heating before drinking. Therefore, it is required that the ink layer will not change color, stain, produce bubbles and lose light after being exposed to steam

since the surface of metal substrate cannot be penetrated, it is easy to produce point increase. Compared with paper printing ink, metal printing offset lithography should use high viscosity ink. The metal surface is a non absorbent surface, and too much wetting water on the layout is easy to produce ink emulsification. Therefore, the water and ink balance on the layout should be achieved by controlling the water film thickness and ink amount on the layout

in metal printing, in order to improve the adaptability of post press processing and make the surface of the printed piece have a certain gloss, polish (post press coating) should be carried out before the printing ink is completely dry to form a uniform and smooth film to avoid color bleeding. At the same time, the metal printing ink should have a certain hardness and toughness, and its properties cannot be changed during repeated heating. The base color coating and glazing oil should have good adhesion

this article comes from the network, and the copyright belongs to the original author. It is only for everyone to share and learn. If the author believes that infringement is involved, please contact us with new electrolyte system (including solvents, solutes and additives), functional electrolyte suitable for high nickel NCM power battery (including additives), electrolyte suitable for energy storage battery (including additives in particular), low-temperature electrolyte The high temperature type (150 ℃) is mainly related to the flame-retardant electrolyte, and we will delete it immediately after verification

Copyright © 2011 JIN SHI